Ground Lights For Yard

YL-MBS16-X is a Φ42x36mm round ground lights for yard fixture built around a single CREE 5050 LED, delivering 240lm at 2W with 90Ra CRI and a 20/30/45/60° adjustable beam. Its IP68-rated 304 stainless steel housing and Φ32mm bore fit narrow cut-outs along garden paths, stepping stones and gravel walkways. DC12/24V input, 0.5m rubber cable, 3-year warranty.

1. CREE SMD5050 LED chip

 

A single CREE 5050 chip drives 240lm from just 2W, so a 20-fixture run pulls under 40W total-letting one 12V/24V transformer power an entire path without adding a second driver circuit.

2. Available beam angles: 20°, 30°, 45°, or 60°

 

Beam angle ships in four options-20°, 30°, 45° or 60°-covering everything from a tight 1m spot to a 3m wide wash, so one SKU replaces four separate part numbers on a bid sheet.

3. 304  stainless steel housing

 

The Φ42x36mm body is IP68-rated and machined from 304 stainless steel, surviving continuous submersion beyond 1m and resisting salt-air corrosion better than 316-grade alternatives priced roughly 30% higher.

 

4. A variety of color temperatures are available to suit different application scenarios.

 

90Ra CRI holds true color under WW/NW/CW/RGB/RGBW options, backed by a 3-year warranty that cuts callback rates versus the 1-year coverage common across the category.

Durable IP68 Ground Lights for Yard - Engineered for Every Outdoor Landscape & Commercial Hardscape Project

Waterproof Ground Lights for Driveway Edging & Vehicle Guidance in Coastal Climates

Traditional surface-mounted path lights along driveways crack under tire impact and corrode rapidly in high-salinity coastal air, forcing property managers into expensive quarterly replacements. Our IP68-rated LED recessed ground lights, built with a full 304 stainless-steel housing, eliminate that cycle entirely. The flush-mount Φ42–Φ62 mm form factor sits below grade level, immune to vehicle contact and salt-fog corrosion-tested to withstand prolonged exposure in seaside environments. With CREE 5050 chips delivering 240–330 lm at DC 12/24 V low voltage, these ground lights for yard driveways provide clear nighttime vehicle guidance while cutting energy costs by over 70 % versus halogen alternatives. Ideal for coastal residential driveways, resort motor courts, and gated-community entrance lanes where long-term durability and zero-maintenance performance are non-negotiable. Beam angles from 20° to 60° allow precise optical tuning for narrow edging wash or wide-area wayfinding.

LED Ground Spotlights for Garden Paths, Stepping Stones & Gravel Walkways

Raised bollard lights along garden stepping-stone paths are prone to mower damage and create tripping hazards on narrow gravel walkways-common complaints from landscape contractors managing residential estates. These mini LED buried spotlights (as compact as 42 × 36 mm) recess completely into soil, pavers, or gravel beds, delivering a subtle ground-level glow that defines every step without cluttering the sightline. Available in round and square bezels with silver, white, or black finish options, they blend seamlessly into any garden ground spotlights layout-from Japanese Zen-style stepping-stone paths to European cottage gravel trails. The 90 CRI rating ensures plants and stone textures render in true, vivid color under warm-white or neutral-white settings. For landscape architects handling OEM assembly of prefabricated garden modules, we supply bulk packs with 0.5 m rubber-sheathed cables ready for daisy-chain low-voltage wiring.

Outdoor In-Ground Spotlights for Tree Uplighting & Ornamental Plant Accent

Generic floodlights pointed at trees waste energy on spill light and create harsh, unflattering shadows that diminish a landscape design's nighttime appeal. A purpose-built ground spot light with a selectable 20° narrow beam transforms tree uplighting-sending a focused column of light along the trunk and into the canopy while keeping surrounding areas dark and dramatic. Our CREE-chip-powered ground lights for trees deliver 330lm from just 3W, so even a 50-fixture resort landscape project draws minimal power. RGB and RGBW color options let hospitality properties rotate seasonal accent palettes-warm amber in autumn, cool blue for winter events-all from the same fixture set. For engineering firms specifying lighting across hotel campus landscaping or municipal park master plans, our team provides one-on-one selection support, 3D installation layout drawings, and free sample kits for on-site mock-up approval before bulk procurement.

Recessed Ground Lights for Retaining Walls, Step Treads & Elevation Changes - Safety-Code Compliant

Unlit stairways and retaining-wall edges in commercial landscapes are liability magnets: slip-and-fall claims in dimly lit elevation-change zones cost property owners thousands annually. Embedding IP68 LED recessed ground lights into step treads and wall caps delivers code-compliant illumination exactly where it matters-at foot level-while eliminating exposed fixtures that vandals or weather can damage. The square-bezel 55 × 55 mm variant sits flush in concrete or stone caps, providing a clean architectural line. DC 12/24V low-voltage operation meets stringent safety requirements for public staircases, ADA-accessible ramps, and fire-evacuation pathways. For large-scale general contractors running annual procurement programs across multiple sites, our in-house factory offers stable production scheduling of 50,000+ units per year with guaranteed lead times, enabling predictable project timelines for phased commercial developments.

FAQ

 

 

01.   What IP rating do your ground lights for yard carry, and can they survive being submerged in standing water after heavy rain?

Our ground lights for yard are rated IP68, which is the highest ingress-protection level available for landscape lighting. This means the fixture is completely dust-tight and can withstand continuous submersion-not just splashing. After heavy rainstorms, standing water pooling around recessed fixtures in low-lying yard areas will not compromise the internal LED module or wiring connections. The seal is achieved through a combination of a precision-machined 304 stainless-steel housing and a vulcanized-rubber cable gland, ensuring long-term integrity even in flood-prone yard zones or irrigation-saturated planting beds.

02.  Will these ground lights for yard corrode if I install them in a coastal property exposed to salt air?

No. Every housing component is manufactured from marine-grade 304 stainless steel, which offers excellent resistance to chloride-induced pitting and crevice corrosion common in high-salinity coastal environments. Unlike zinc-alloy or aluminum fixtures that begin to show surface degradation within 6–12 months near the ocean, our 304 SS construction maintains its structural and aesthetic integrity for years. We routinely supply coastal resort and beachfront residential projects where salt-fog exposure is constant and aggressive.

03.  What beam angle options are available, and how do I choose the right one for yard pathway lighting versus tree uplighting?

We offer four beam angles-20°, 30°, 45°, and 60°-across the entire product range. For yard pathway edging and driveway guidance, the 45° or 60° option provides a comfortable spread that covers standard walkway widths from a single-side installation. For tree uplighting and ornamental-plant accent, the 20° or 30° narrow beam concentrates light along the trunk and into the canopy without wasting energy on surrounding ground. Our engineering team can review your landscape layout and recommend the optimal beam angle for each fixture position at no additional cost.

04.  Can I use these ground lights with my existing 12-volt landscape transformer?

Yes. All models operate on DC 12V or 24V, making them directly compatible with standard low-voltage landscape transformers already installed in most residential and commercial yards. Each 2W fixture draws only 0.17A at 12V, so a single 150W transformer can power over 60 fixtures with headroom. The 0.5 m rubber-sheathed cable on each unit connects easily to buried low-voltage trunk lines using standard waterproof wire connectors, with no licensed-electrician rewiring required.

05.  What is the color rendering index (CRI), and why does it matter for my yard lighting?

Our ground lights for yard deliver a CRI of 90 Ra, which is considered high-fidelity color rendering. In practical terms, this means the warm-white or neutral-white light output reproduces the natural colors of your plants, stone, mulch, and hardscape materials with lifelike accuracy-greens look genuinely green, sandstone retains its warmth, and brick shows its true red-brown tone. Lower-CRI fixtures (typically 70–80 Ra in budget products) cast a grayish or yellowish tint that flattens textures and makes expensive landscaping look dull at night.

06.  Do you offer RGB or RGBW color-changing options for seasonal or event lighting in yards?

Yes. Every model is available in WW (warm white), NW (neutral white), CW (cool white), RGB, and RGBW configurations. The RGBW variant is especially popular for residential yards and hospitality properties that want to switch between functional white illumination for everyday use and dynamic color scenes for holidays, parties, or branded events. RGBW fixtures are controlled via standard low-voltage RGB controllers or DMX systems, and we can advise on compatible control hardware during the specification stage.

 

ABOUT US

SHENZHEN YLSTAR LIGHTING CO, LIMITED is a professional manufacturer and exporter that is concerned with the design, development and production of extrior Lighting, indoor lighting, Advertising lighting and led strip solution. We are located in SHENZHEN, with conveninet transportation access. All of our products comply with international quality standards and are greatly appreciated in a variety of different markets throughout the world.

 

CERTIFICATION

Our well-equipped facilities and excellent quality control throughout all stages of production enables us to guarantee total customer satisfaction. Besides, we have received ISO90001, CCC,CE, ROHS,FCC,SAA,TUV, ETL, cETL certification. As a result of our high quality products and outstanding customer service, we have gained a global sales network reaching Europe, North America, Australia and other countries in the world.

 

WHY WORK WITH US

★Professional Sales and after-sales service Team

Experienced team, fast reaction.

Offering one-stop purchase service and one-stop lighting solution.

★Patented design

We design and manufacture led light with our own mold & technology.

★100% Inspection

All products must pass 3 times inspection before shipment.

All products are under 4 hours semi-product aging and another 4 hours finished product aging.

EXHIBITION

Hong Kong Spring Lighting Fair / Hong Kong Autumn Lighting Fair