1W Mini surface mount deck lights

1. Efficacy - 110 lm/W from a CREE brand chip

 

Each surface mount deck light runs a single CREE 5050 chip at DC12V/1W for 110lm (with 20°/30°/45°/60° beam angle options.)- 110lm per watt. 48 units draw 48W total, so one 60W transformer at 80% load powers a full 48-point deck on a single circuit instead of three, cutting driver cost and trenched cable runs proportionally. CRI measures 90Ra, above the 70–80Ra range common in low-cost deck lighting. Redwood, ipe, and gray composite boards hold their daytime color values under the beam rather than shifting yellow-green.

2. IP67, 304 Stainless Steel + 6063 Aluminum

 

IP67 certifies 30 minutes at 1m submersion, covering standing water on flat decking and close-range pressure washing. The 304 stainless bezel sits over a 6063 aluminum body, placing the corrosion-resistant alloy on the exposed face - the material pairing specified for pool coping and installs within 500m of saltwater. Body depth is 22mm behind a Φ28mm hole, so the fixture installs in 25mm composite boards and hollow-core decking that reject recessed lights needing 40mm+ clearance. The Φ42 flange covers the cut edge - one pass with a 28mm spade bit, roughly 90 seconds per point.

3. Multiple Beam angles and Pre-Wired PVC Cable, DC Connector

 

Every unit ships with 1m of PVC cable terminated in a DC connector. A 12-light run plugs into splitters directly, removing 24 stripped, soldered, and heat-shrunk joints from the install - and with them the most frequent field failure on deck lighting: hand-made connections sitting in a wet joist cavity. One housing carries four optics: 20° for grazing 2.5m risers, 30° and 45° for tread and border washing at 300–600mm spacing, 60° for wide step coverage. Specifiers keep a single hole size and finish across the whole deck and vary only beam angle by zone - one hardware SKU, four lighting effects.

4. DC12V SELV, 3-Year Warranty

 

DC12V falls inside SELV limits, so wet deck and poolside zones accept the fixture without conduit under most codes, and homeowner installation stays outside licensed-electrician scope. A 3-year warranty covers a 100-light commercial deck through three full freeze-thaw and pool seasons. Three stocked finishes - silver, white, black - match aluminum railing posts, painted trim, and dark composite decking without custom powder coating or its 15–20 day lead time. All three share the same Φ42 flange and Φ28mm hole, so finishes mix across one deck with no change to drilling.

1. Timber & Composite Deck Borders

Surface mount deck lights install directly into 25mm cedar, ipe, or WPC boards - 22mm body depth behind a Φ28mm hole, no 40mm recess cavity required. Set 45° or 60° optics at 400–600mm centres along the perimeter; the Φ42 stainless flange caps the cut edge and 90Ra CRI holds the board's natural grain color after dark.

2. Stair Treads & Risers

One light per tread, 20° or 30° beam, mounted 60–80mm in from the nosing puts 110lm on the walking surface without glare at eye level on a descent. On a 12-step flight, 12 units draw 12W total - a single DC12V run off one 20W transformer, no per-step driver.

3. Pool Coping & Spa Surrounds

IP67 covers 30 minutes at 1m submersion, so splash-out and standing water on wet-set coping are within rating. The 304 stainless bezel handles chlorinated splash at the exposed face, and DC12V SELV operation lets fixtures sit in poolside zones without conduit under most codes - outside licensed-electrician scope for retrofit work.

4. Marina Docks, Boardwalks & Jetties

304 stainless over 6063 aluminum is the standard pairing for installs within 500m of saltwater. On floating docks and boardwalk decking, the 1m pre-wired PVC cable with DC connector plugs straight into splitters, eliminating hand-soldered joints in a wet joist cavity - the most frequent field failure on marine deck lighting.

5. Rooftop Terraces & Hospitality Decks

Hotel and restaurant terraces photographed for booking listings need 90Ra rather than the 70–80Ra of budget fixtures: redwood, ipe, and gray composite hold daytime color values and skip the color-correction pass on night shots. 1W per point keeps a 60-light terrace at 60W - well inside rooftop circuit allowances.

6. Retaining Walls, Planter Caps & Hardscape

Face-mounted into stone caps, wall veneer, and planter edges, 20° optics graze 2.5m of vertical surface from a single point. Silver, white, and black finishes are stocked to match aluminum posts, painted trim, and dark stone - no custom powder coat, no 15–20 day coating lead time, same Φ28mm drill across all three.

7. Pergolas, Fences & Railing Posts

The Φ42×22mm body fits 40mm+ post caps, fence rails, and pergola beams where recessed fixtures won't seat. Mixing beam angles by zone - 20° down a post, 60° across a bench - keeps one hole size and one housing SKU across the whole structure while varying only the optic per position.

8. Landscape Paths, Steps & Garden Walls

At 1W and 110lm, a 30-point path or step run totals 30W on a DC12V circuit - a standalone low-voltage system with no mains distribution or trenched conduit to each fixture. IP67 and 304 stainless cover irrigation overspray, ground-level splash, and pressure washing at close range.

FAQ

 

 

01. What is the best lighting for an outdoor deck?

A: The best lighting for an outdoor deck combines low-voltage LED step lights, post cap lights, and recessed floor dots for a safe, layered, and glare-free glow.

02. How to install a surface mount light?

A: Installing a surface-mounted light involves turning off the power, securing the mounting bracket to the ceiling, connecting the electrical wires, and attaching the fixture.

03. What are common mistakes when installing a light?

A: Common mistakes when installing a light include failing to turn off power at the breaker, poor wire connections, and improper grounding

04. What is the lifespan of a surface mounted light?

A: The lifespan of Surface Mounted Deck Lights Round depends mainly on material quality, component selection, heat dissipation design, usage environment and maintenance. A high‑quality professional model can easily reach 50,000 hours - enough for 10 to 17 years of normal use.

05. Do I need an electrician?

A: Low-voltage (12V) systems plug into standard GFCI outlets via a transformer and are safe for DIYers. Line-voltage (120V) systems require professional installation and strict code compliance.

 

 

ABOUT US

SHENZHEN YLSTAR LIGHTING CO, LIMITED is a professional manufacturer and exporter that is concerned with the design, development and production of extrior Lighting, indoor lighting, Advertising lighting and led strip solution. We are located in SHENZHEN, with conveninet transportation access. All of our products comply with international quality standards and are greatly appreciated in a variety of different markets throughout the world.

 

CERTIFICATION

Our well-equipped facilities and excellent quality control throughout all stages of production enables us to guarantee total customer satisfaction. Besides, we have received ISO90001, CCC,CE, ROHS,FCC,SAA,TUV, ETL, cETL certification. As a result of our high quality products and outstanding customer service, we have gained a global sales network reaching Europe, North America, Australia and other countries in the world.

 

WHY WORK WITH US

★Professional Sales and after-sales service Team

Experienced team, fast reaction.

Offering one-stop purchase service and one-stop lighting solution.

★Patented design

We design and manufacture led light with our own mold & technology.

★100% Inspection

All products must pass 3 times inspection before shipment.

All products are under 4 hours semi-product aging and another 4 hours finished product aging.

 

EXHIBITION

Hong Kong Spring Lighting Fair

Hong Kong Autumn Lighting Fair